CLAAS DEUTZ D 2011 w, TD 2011 w, TCD 2011 w Repair Manual

CLAAS DEUTZ D 2011 w, TD 2011 w, TCD 2011 w Repair Manual

This is the CLAAS DEUTZ D 2011 w, TD 2011 w, TCD 2011 w repair manual, as a PDF. It runs to 544 pages in 86 chapters.

It covers the CLAAS DEUTZ D 2011 w, TD 2011 w, TCD 2011 w. It is CLAAS's own documentation from the CLAAS service documentation, the same information the dealer workshops work with.

What is inside

The largest sections are Dismantling and assembling the front cover (24 pages), 8 Special tools (18 pages), Renew toothed belt and tensioning pulley (12 pages). The chapters are:

• Front Page (2 pages)
• Checking the compression pressure (6 pages)
• Mounting engine on assembly block and demounting (6 pages)
• Setting valve clearance (6 pages)
• Removing and installing the rocker arm and rocker arm bracket (4 pages)
• Disassembling, assembling and checking the rocker arm and rocker arm bracket (6 pages)
• Removing and installing cylinder head (8 pages)
• Checking piston overhang (6 pages)
• Removing and installing the valves (6 pages)
• Checking the valves (4 pages)
• Checking the valve guide (4 pages)
• Checking the valve lag (2 pages)
• Checking the axial clearance of the crankshaft (6 pages)
• Checking the crankshaft (6 pages)
• Renewing the crankshaft sealing ring (flywheel side) (4 pages)
• Renewing the crankshaft sealing ring (opposite side to flywheel) (4 pages)
• Checking the con rod (10 pages)
• Removing and installing small end bush (6 pages)
• Removing and installing the crankshaft (10 pages)
• Removing and installing the piston and con rod (10 pages)
• Checking the piston (4 pages)
• Checking the piston rings and piston ring grooves (6 pages)
• Removing and installing the piston cooling nozzles (2 pages)
• Removing and installing the crankcase bleeding (4 pages)
• Checking the cylinder (4 pages)
• Removing and installing the front cover (6 pages)
• Dismantling and assembling the front cover (24 pages)
• Removing and installing rear cover (4 pages)
• Removing and installing the connection housing (4 pages)
• Removing and installing, testing camshaft bearing (8 pages)
• Renew camshaft sealing ring (opposite side to flywheel) (4 pages)
• Renew toothed belt and tensioning pulley (12 pages)
• Removing and installing the toothed belt wheel (8 pages)
• Removing and installing the camshaft (6 pages)
• Checking the camshaft (4 pages)
• Removing and installing the control linkage (4 pages)
• Removing and installing the guide bushes (Control linkage) (12 pages)
• Removing and installing the impulse transmitter (4 pages)
• Removing and installing the exhaust line (4 pages)
• Removing and install the charge air line (4 pages)
• Removing and installing the turbocharger (8 pages)
• Removing and installing the intake manifold (4 pages)
• Removing and installing the exhaust gas return valve (8 pages)
• Removing and installing the exhaust gas return pipe (8 pages)
• Removing and installing the exhaust gas collection pipe (Exhaust gas recirculation) (6 pages)
• Removing and installing the sensor (Exhaust gas recirculation) (4 pages)
• Removing and installing the magnet clip (Exhaust gas recirculation) (4 pages)
• Removing and installing the lifting magnet (Start amount release) (4 pages)
• Renewing the injection lines (4 pages)
• Removing and installing the fuel injector pump (12 pages)
• Check start of injection (12 pages)
• Determining the thickness of the shim (4 pages)
• Removing and installing the fuel injectors (6 pages)
• Checking fuel injectors (6 pages)
• Removing and installing the lifting magnet (charge air pressure-dependent full load stop) (4 pages)
• Installing and removing charge air pressure-dependent full load stop (4 pages)
• Removing and installing fuel pipes (8 pages)
• Removing and installing the fuel filter console (6 pages)
• Removing and installing the fuel supply pump (6 pages)
• Removing and installing the lubricating oil pump (4 pages)
• Removing and installing the oil suction pipe (4 pages)
• Removing and installing the lubricating oil pan (metal sheet lubricating oil pan) (8 pages)
• Removing and installing the lubricating oil cooler (4 pages)
• Removing and installing the oil pressure regulating valve (4 pages)
• Removing and installing the oil filter console (6 pages)
• Removing and installing the oil pressure switch (4 pages)
• Removing and installing the thermostat (Lubricating oil cooler) (4 pages)
• Removing and installing the control line (4 pages)
• Removing and installing the coolant pump (4 pages)
• Checking the thermostat (in the removed state) (4 pages)
• Removing and installing the thermostat (4 pages)
• Removing and installing the thermostat housing (6 pages)
• Removing and installing temperature transmitter (4 pages)
• Removing and installing the lifting magnet (Engine shutdown) (4 pages)
• Removing and installing the V-belt pulley (4 pages)
• Renew V-belts, check V-belt tension (8 pages)
• Removing and installing the flywheel (4 pages)
• Renewing toothed starter ring on the flywheel (2 pages)
• Removing and installing the hydraulic pump (4 pages)
• Renew toothed belt and tensioning pulley (Hydraulic pump) (6 pages)

What you can do with it

• Find the cause of a fault before replacing parts
• Remove, overhaul and refit components
• Set clearances and adjustments to the factory values
• Use the right torque values and tightening sequences
• Follow the exploded views and photos when taking assemblies apart

Questions and answers

Which machines does this manual cover?
The CLAAS DEUTZ D 2011 w, TD 2011 w, TCD 2011 w, as named in the title.

Is it the original manufacturer manual?
Yes. It is CLAAS's own documentation, not a third-party reprint or a summary.

How many pages does it have?
544 pages, in 86 chapters listed above.

How do I receive it?
It is a PDF, available as an instant download right after payment. You can read it on a computer, tablet or phone or print the pages you need. No printed book is shipped.